|
|
|
|
|
|
Non Cut Crankshaft - 4g63 6 Bolt - Polished w/Bearings
|
Our Price: $499.99
Sale Price: $349.99
You Save $150.00
|
|
|
These are our Virgin Crankshaft kits, that has been inspected, measured for run out, and polished. These are NON CUT, meaning if you are planning on running high HP on a stock crank, this is the one you want. We have all heard the rumors about cutting cranks and removing the strength, so if you are in need of one, here they are! These are recommended for the 500HP Plus range, when not going to a Eagle or Magnus crankshaft. These come with Engine Pro Aluminum Bore Bearings. Great for High Performance applications and great street ability!
|
|
|
|
|
|
|
|
|
|
|
|
|
4G63 Connecting Rod and Piston - 6 Bolt Turbo
|
|
Our Price: $49.99
|
|
|
This is a Used Connecting Rod and Piston combo for the turbo 6 bolt 4G63 engines. Wrist pin pivots smoothly. They are in reusable condition, but like all used pistons, and ring grooves should be cleaned.
|
|
|
|
|
|
|
|
|
|
|
|
|
Engine Block - Turbo 6 Bolt - 90-92
|
|
Our Price: $400.00
|
|
|
This is a Good Used Engine Block, for the 90-92 6-Bolt Turbo DSMs. This is a bare block, and only comes with the main caps, and freeze plugs. This does not include the rear main seal housing, front oil pump plate, or the oil squirter's. These blocks, like most blocks will need to be machined at your local machine shop. They are threaded to accept oil squirter's, and all other OEM components. We offer custom machining, hot tanking, and prepping for these blocks so they are ready to go when you get them! Feel free to ask any questions, Thanks!
|
|
|
|
|
|
|
|
|
|
|
|
|
Balance Shaft - Belt Driven 90-99
|
|
Our Price: $34.99
|
|
|
This is a Used Balance Shaft for the 90-99 4G63 engines. This is the one that is belt driven, with the small timing belt. (MD102783) Same on all DSM 4G63 engines. These are in good reusable condition, without any scaring on the bearing surface.
|
|
|
|
|
|
|
|
|
|
|
|
|
Oil Pickup Strainer - 4G63 - 6 Bolt
|
|
Our Price: $14.99
|
|
|
This is a Used Oil Pickup Stainer for the 6 Bolt engines.
|
|
|
|
|
|
|
|
|
|
|
|
|
Connecting Rod - 90-92 6 Bolt
|
|
Our Price: $34.99
|
|
|
This is a Used Connecting Rod for the 90-92 6 Bolt 4g63 engines. These are the "Big Rods" that are used for the Frankenstein Engines, but are not machined for the 2G Pistons. These rods have had the pistons pressed out, and have been cleaned and inspected. New Piston and Wrist Pin install can be done at your local machine shop, when using OEM press wrist pins. These will come with the rod studs, but need to be replaced. Feel free to contact us with any questions on these connecting rods.
|
|
|
|
|
|
|
|
|
|
|
|
|
Oil Pump Balance Shaft - 90-99 4g63
|
|
Our Price: $34.99
|
|
|
This is a Good Used Oil Pump Balance Shaft for the 66 and 7 bolt 4g63 engines, from 90-99. OEM Part # MD102782
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Oil Pump Gear Set - 6 Bolt
|
|
Our Price: $9.99
|
|
|
This is a good used set of gears for the 6 bolt oil pumps. These are Straight Cut Gears!
|
|
|
|
|
|
|
