|
|
|
|
|
|
Non Cut Crankshaft - 4g63 6 Bolt - Polished w/Bearings
|
Our Price: $499.99
Sale Price: $349.99
You Save $150.00
|
|
|
These are our Virgin Crankshaft kits, that has been inspected, measured for run out, and polished. These are NON CUT, meaning if you are planning on running high HP on a stock crank, this is the one you want. We have all heard the rumors about cutting cranks and removing the strength, so if you are in need of one, here they are! These are recommended for the 500HP Plus range, when not going to a Eagle or Magnus crankshaft. These come with Engine Pro Aluminum Bore Bearings. Great for High Performance applications and great street ability!
|
|
|
|
|
|
|
|
|
|
|
|
|
Non Cut Crankshaft - 4G63 7 Bolt - Polished w/Bearings
|
Our Price: $499.99
Sale Price: $375.00
You Save $124.99
|
|
|
This is a Virgin Crankshaft, that has not been cut! These are our good cranks, that have been measured for run out, and then have been cleaned and polished! These are ready to install, and come with Clevite Rod and Main Bearings. This is the crankshaft kit that you want if going over the 500HP mark, and you do not want to go to an Eagle or Magnus Crankshaft. These also will work with the Evo 8-9, just specify so we can send you the right bearings.
|
|
|
|
|
|
|
|
|
|
|
|
|
4G63 Connecting Rod and Piston - 6 Bolt Turbo
|
|
Our Price: $49.99
|
|
|
This is a Used Connecting Rod and Piston combo for the turbo 6 bolt 4G63 engines. Wrist pin pivots smoothly. They are in reusable condition, but like all used pistons, and ring grooves should be cleaned.
|
|
|
|
|
|
|
|
|
|
|
|
|
Engine Block - Turbo 6 Bolt - 90-92
|
|
Our Price: $400.00
|
|
|
This is a Good Used Engine Block, for the 90-92 6-Bolt Turbo DSMs. This is a bare block, and only comes with the main caps, and freeze plugs. This does not include the rear main seal housing, front oil pump plate, or the oil squirter's. These blocks, like most blocks will need to be machined at your local machine shop. They are threaded to accept oil squirter's, and all other OEM components. We offer custom machining, hot tanking, and prepping for these blocks so they are ready to go when you get them! Feel free to ask any questions, Thanks!
|
|
|
|
|
|
|
|
|
|
|
|
|
Engine Block - Turbo 7 Bolt - 93-94
|
Our Price: $400.00
Sale Price: $175.00
You Save $225.00
|
|
|
This is a good Used Engine Block, for the 93-94 Turbo 7 Bolt DSMs. These bare blocks have not been honed, or bored, and come with the main caps, and freeze plugs. They do not include the rear main seal, front oil pump plate, oil pickup, or oil squirter's. They are ready to be prepped for your rebuild, and accept all stock components. These are Standard Bore, but most likely need to be bored .020.
|
|
|
|
|
|
|
|
|
|
|
|
|
Balance Shaft - Belt Driven 90-99
|
|
Our Price: $34.99
|
|
|
This is a Used Balance Shaft for the 90-99 4G63 engines. This is the one that is belt driven, with the small timing belt. (MD102783) Same on all DSM 4G63 engines. These are in good reusable condition, without any scaring on the bearing surface.
|
|
|
|
|
|
|
|
|
|
|
|
|
Crankshaft - 1.8 90-94
|
|
Our Price: $129.99
|
|
|
This is a good Used Crankshaft for the 1.8 DSMs. These crankshafts did not have bad bearings, and did not knock. Always measure and plasti-gauge during your build.
|
|
|
|
|
|
|
|
|
|
|
|
|
Piston and Rod Assembly - 1.8
|
|
Our Price: $24.99
|
|
|
This is a Used Piston and Rod Assembly for the 1.8 DSMs.
|
|
|
|
|
|
|
|
|
|
|
|
|
Oil Pickup Strainer - 4G63 - 6 Bolt
|
|
Our Price: $14.99
|
|
|
This is a Used Oil Pickup Stainer for the 6 Bolt engines.
|
|
|
|
|
|
|
|
|
|
|
|
|
Piston and Rod Assembly - Non Turbo 6 Bolt
|
|
Our Price: $49.99
|
|
|
This is a Used Piston and Rod Assembly for the Non Turbo 6 Bolt. These have the 9.0 Compression, for the Non turbo application.
|
|
|
|
|
|
|
